![]() Have you recently made any changes on the printer before the issue started? To provide you with an accurate solution, I'll need a few more details: Don't worry as I have a few suggestions which should help you resolve this issue. Chinese for engaging in HP support Forums! This is a wonderful location to converse with the community, get assistance and find tips! I understand you are having issues printing in color from your HP Photosmart Printer.Business PCs, Workstations and Point of Sale Systems.Printer Wireless, Networking & Internet.DesignJet, Large Format Printers & Digital Press.Printing Errors or Lights & Stuck Print Jobs.Notebook Hardware and Upgrade Questions.If the above steps do not solve the problem, contact your dealer, download SeaTools diagnostic tools, or contact Seagate Support. If FDISK does not detect the drive, run the FDISK program with FDISK /STATUS to verify the drive is present. If the computer does not seem to recognize the drive, verify the drive is enabled by the SCSI host adapter setup utility. Set the ID so that each device on the SCSI chain has a unique ID. If the drive spins, but there is no LED on/off activity, check the SCSI ID setting. If the drive does not spin up, check that the power connector and the interface cable are securely attached. Most operating systems provide partitioning and high level formatting utilities (i.e. ![]() If performing a low level format, take care not to interrupt the format to avoid damaging the drive. DO NOT over-tighten the screws.Īll Seagate SCSI drives are low level formatted at the factory and should not need to be low level formatted. Secure the drive using four 6-32 UNC mounting screws. Drive models ending in LC cannot be configured to provide termination power to the bus.Īttach one end of the interface cable to the connector on the host adapter.Īttach the interface connector and a power connector to the drive. Check the user's manual for your host adapter. Usually, the host adapter provides term power. The default configuration results in the drive not supplying termination power to the bus. Use only active SE or LVD terminators.Īctive terminators must receive power from some source. LVD drives do not have any provision for onboard termination therefore, termination for LVD drives must come from another device or from an external terminator. The SCSI host adapter normally will provide termination for the controller end, therefore only terminate the last drive on the end of the cable. Only the devices at each physical end of a SCSI bus need to be terminated. If you are installing a drive model ending in LC (uses 80-pin SCA connector), the host normally sets the ID over the I/O interface. The SCSI host adapter usually uses SCSI ID = 7. Most Seagate SCSI drives come with no jumpers on SCSI ID (SCSI ID = 0). Terminator Power – Host adapter or other device provides term power (default).Įach SCSI device must have a unique SCSI ID. Parity Check – Enable Parity check (default). Write Protect – Write Protect Off (default). Motor Start – Disable motor start (default).ĭelay Motor Start – Disable Delay motor start (default). SE I/O – No jumper so the device can multimode (default). The primary benefits of LVD include faster transfer rates, reduced power consumption, increased cable lengths, and improved device connectivity. ![]() This multimode capability provides backward compatibility so you can use it with or without an LVD-capable host adapter. Low Voltage Differential (LVD) drives can operate in single-ended (SE) or LVD mode. Most new SCSI hard drives are Ultra2/3 LVD (80 MB/s or 160 MB/s) capable. Standard interface cable and SCSI host adapter.Īn unused drive power cable for your new drive. Phillips screwdriver and four 6-32 UNC drive mounting screws. Handle the drive by the edges of the frame.ĭo not apply pressure or attach labels to the circuit board or the top cover of the drive. Turn off the power to the host system during installation. Protect the drive from static discharge by wearing a grounded wrist strap. Keep the drive in the protective anti-static container until ready to install.
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |